I would be happy to answer that question for you. The main difference between the Curt Front Hitch Receiver item # C87FR and the Draw-Tite Front Hitch Receiver Item # 65081 is the difficulty in installation. The Curt is way easier to install. You have to remove the front air dam and splitter to install the Draw-Tite. They both have identical capacities with a 9,000 lbs line pull and a 500 lbs vertical load limit. Since the capacities are the same I recommend the Curt item # C87FR based... view full answer...
The Curt Front Mount Hitch Receiver # C31008 fits 2008 - 2010 Ford Super Duty pickups and some 2009 - 2011 motorhomes while the Curt Front Mount Hitch Receiver # C31068 fits a 2009 - 2014 Ford F-150, a 2009 - present Ford Expedition, and a 2009 - present Lincoln Navigator.
Since you were looking at front hitches for a 2013 Ford Expedition you want the Front Hitch # C31068. view full answer...
We currently have two front mount trailer hitch receivers for your 1996 Chevrolet K1500, the Draw-Tite Front Mount Trailer Hitch Receiver part # 65005 and the Curt Front Mount Trailer Hitch Receiver part # 31042. They both have a 9,000 lb line pull and 500 lb vertical load weight capacity. They also both install using three holes on each side.
The main difference between them is that the Curt hitch hangs down more. This means it will be more visible but it also means that if you have... view full answer...
The Curt Front Mount Trailer Hitch Receiver # C31015 does sit very far behind and below the factory bumper. When we installed it on a 2015 Ram 2500 like yours in our shop the hitch receiver pin sat 10" behind the leading front edge of the bumper. Since there are several different winches and mounts available and without knowing how the new bumper will change that 10" measurement it is hard to know exactly what will fit until the new bumper is installed. My biggest concern with this comes... view full answer...
Yes. The Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" # 31241 is a confirmed fit on your 2009 Nissan Frontier and will give you a 2" receiver to carry a bike rack on the front of your truck.
I've linked an installation video of this hitch you can check out, as well as our entire selection of bike racks that will fit in a 2" hitch in case you don't have one already. view full answer...
There are virtually no structural differences between the Curt Front Mount Trailer Hitch Receiver part # 31114 and the Draw-Tite Front Mount Trailer Hitch Receiver part # 65022 for your 2000 Ford F-250. They both install in the exact same location and allot for a 500/5,000 Lb vertical load and line pull rating. The main reason for the price difference is that the Curt hitch is made in the USA and has a more resistant powder coating.
I have attached a sample install video for you as well. view full answer...
The Curt Front Mount Trailer Hitch Receiver # C31083 and Draw-Tite Front Mount Trailer Hitch Receiver # 65067 are currently the only 2 front mount receivers that are custom fit for your 2015 Ford F-150 XLT.
Both receiver have the same 9,000lb line pull rating for using your winch and both will support a tongue weight of up to 500lbs which will allow you to use it for other things during the summer. Visually both receivers appear the same and have very similar construction.
If you plan... view full answer...
The Curt # C31063 front mounted receiver are fits for multiple model years of the Ford Ranger and Mazda B Series trucks. It is a fit for your 2002 Ford Ranger. Once installed, the receiver tube would sit below the front bumper.
I have attached the installation instructions for you to check out. view full answer...
The installion instructions for the Draw-Tite Front Mount Trailer Hitch Receiver part # 65049 do not require that the front lower bumper spoiler be removed therefore yes, I believe you can leave it in position while you install the trailer hitch. The process of removing the front lower bumper spoiler was done to give our viewers a better look at what was going on which is why it was removed in the video.
Please note that if you don't want to do any trimming of the front lower bumper spoiler... view full answer...
The difference is that the receiver on the Curt Front Hitch # C31078 will sit below the bumper on your F-350 while the receiver on the EcoHitch # 306-X7904 will actually sit in the same location as your front license plate and comes with a plate that can move out of the way when you need to utilize the front hitch.
I really like the EcoHitch simply because it hides behind the license plate for a clean, OEM look on your truck. Attached is an installation video of the EcoHitch on a 2021... view full answer...
The Draw-Tite Front Mount Trailer Hitch Receiver # 65046 and Curt Front Mount Trailer Hitch Receiver # C31017 that fit your 2006 Dodge Ram 3500 are very similar in the mounting location. The main difference that I see is where the cross tube and receiver come together. The cross tube on the Curt is cut and the receiver passes through it. While the Draw-Tite receiver is welded to the bottom of the cross tube. Not having that cut in the cross tube will make it stronger which is why I would... view full answer...
There are few differences between the Draw-Tite Front Mount Trailer Hitch Receiver # 65067 and Curt Front Mount Trailer Hitch Receiver # C31083 that fit your 2020 Ford F-150, with the main difference being ground clearance. The Curt hitch does have slightly better ground clearance, as the bottom of the hitch will at least be level with your F-150's air dam at its lowest. The Draw-Tite hitch will be slightly below that, so with all things being equal, the Curt option is going to be better... view full answer...
The Draw-Tite Front Mount Trailer Hitch Receiver # 65067 and the Curt Front Mount Trailer Hitch Receiver # C31083 are both confirmed to fit your 2020 Ford F-150. They are very similar in design and mount to the same locations on the frame, however the Draw-tite will be slightly lower than the Curt hitch.
Both hitches require trimming of the lower air dam, but you can see in the photos that the cut line and where the receiver tube is slightly higher with the Curt.
Both front hitches... view full answer...
I would be happy to clarify. The Curt Front Mount Trailer Hitch Receiver item # C31023 fits a 2013 Chevrolet Silverado 2500 or 3500. This front mount hitch sits below the front bumper. I have attached an installation video.
For a 2013 Chevrolet Silverado 1500 LT you will want the Curt Front Mount Trailer Hitch Receiver item # 31322. This one mounts below the front bumper as well. I have also linked an installation video. view full answer...
For the 2017 Ram 2500, Curt offers the # C31015 and Draw-Tite offers the # 65063. The difference between the two is that they mount in different places on the front of the vehicle, and the Curt model fits 4WD trucks only.. The Curt models installs so that the receiver tube sits under the front truck bumper while the Curt model's receiver mounts in a cutout in the center of the bumper so the receiver tube sits just above the license plate. The Draw-Tite version fits both 2 WD and 4 WD models.... view full answer...
The Curt Front Mount Trailer Hitch Receiver # C31069 provides the most ground clearance out of the three available for your 2017 Chevy Silverado 1500.
To give you a better idea of how low each hitch would sit once bolted to your frame I have attached photos showing the
distance from the frame brackets to the bottom of the hitch receiver for each of the following three hitches:
# C31069 - 9.5 inches
# 65064 - 9.62 inches
# C31012 - 10.9 inches view full answer...
Yes, the Curt Front Mount Trailer Hitch Receiver part # C22NR is the same as 31092 and it's a fit for 2023 Chevrolet Silverado 1500. This will be a great addition to your truck without any drilling required. It can be used for anything from mounting a winch or snowplow to easily maneuvering a trailer into a tight parking spot. view full answer...
The front mount trailer hitch options for a 2019 Chevrolet Tahoe, the Curt Front Mount Trailer Hitch Receiver part # C31073 and Draw-Tite Front Mount Trailer Hitch Receiver part # 65064 both require a slight trimming of the front lower bumper fascia. I took a look at some install photos of either hitch and it does appear that the Curt hitch offers more ground clearance so that is what I recommend. Furthermore, the Curt hitch has a clearer install look since the crosstube is more hidden... view full answer...
Curt front mount hitches # C31069 and # C31012 are nearly identical with the exception of what all each will fit. The newer C31069 is designed just for trucks whereas the C31012 also fits some GM SUVs such as the Yukon and Escalade.
But as far as how they will fit on your 2015 GMC Sierra 1500 they will be the same. I have linked instructions for both. Both require front fascia/air dam trimming so the bottom of the receiver will sit about 1 inch lower than the bottom of the fascia/air dam. view full answer...
I would be happy to help you find a front mount receiver hitch for your 2018 Ram 3500. I recommend the Curt Front Mount Hitch item # C31067. It has a 9,000 lbs line pull capacity and a 500 lbs vertical load limit.
I have attached pictures of both so you can see what the final product looks like. Whichever one you pick needs to be determined by your needs though. If you are going to be using a snow plow you will want the Curt item # C31067 because of the higher mounting point. view full answer...
Go To Results